Category Archives: Events

Mein Bierwagen Part 3 – Bicycle Wheel Attachment

Besides being able to easily move my keezer to the backyard, the two coolest things about Mein Bierwagen are usage of bicycle wheels and the way I load the keezer on the dolly.  I had searched around trying to find the best wheels for the job, but when buying wheels separately from something, you can sometimes pay more than buying a complete thingamajig that has the wheels in the first place.  When working in the garage it hit me, literally in the head.  The tire of the bike hanging in the garage.  Voila!

Difficulty: level_3

This project just requires some basic building skills, but you might need some help getting the keezer onto the Bierwagen.

Posts for this Project:

Part 1: Introduction
Part 2: Building of the frame
Part 3: Bicycle wheel attachment (this post)
Part 4: Getting the keezer onto the Bierwagen
Part 5: Keezer collar
Part 6: Storage of the Bierwagen

Overview:

This post will show how to create and attach the bicycle wheels to the Bierwagen.

Affiliate Links

Helpful tools:

Cut off saw

I do use the cut off saw more frequently than I had anticipated.  It’s pretty handy for cutting through metal bars and tubes.  I got an inexpensive model at Harbor Freight.

Step bit

or Step bit set

The step bits are really useful for other uses in brewing equipment.  I’ve used them to create airlock grommet holes in bucket lids before and spigot holes as well.  I think the most preferred method for putting holes in kettles is a hole saw or punch, but I think these would do a great job as well.

Fabrication:

You might recognize the L-channel (AKA angle iron or L bracket) from the Keezer Dolly project.  You’ll need 4 short sections to attach both wheels to the frame.  I cut approximately 6″ sections.

015-4 - Cutting Channel

You’ll then pick one of the already round holes and open it up using the step bit.  I measured the diameter of the opening on the forks of both of our bikes and matched the hole size on the bracket.  The wheel actually rides on a very narrow section of the axle that sticks out of the wheel hub on both sides, then a cam clamp snugs it up tight.

015-4 - Step bit to open up hole

After you have opened up the hole, you’ll need to make the hole a slot that the wheel can drop into.  You are basically going to mimic what is on the bicycle fork.

015-4 - Bracket Slot

You’ll also want some lag bolts to attach the new mounting brackets to the frame.  I used some 3/16″ lag bolts with a washer.  This is where you’ll need some careful measurement and alignment.

Since the L bracket is much thinner than the bike fork attachment point, you’ll need some washers to add thickness.  The only washers I could find that were thick enough were some lock washers or split washers.  They will stack up like shown in the pictures below.

015-4 - Stackup

015-4 - Axle with split washer

The important washer dimensions are shown below.  My axles required a 1/2″ ID (inner diameter) washer to fit around the bearing surface of the axle.

015-4 - Washer diameter measurements

The thickness of the lock washer (when compressed) was about 3/32″.

015-4 - Washer thickness measurements

Here is an alternate arrangement that also works if you don’t need a ton of thickness.

015-4 - Alternate Washers

I’m going to use some car talk here.  If you’ve opened up the holes properly on the brackets, you should still have a zero camber wheel angle.  The main challenge will be to ensure there is zero toe, or the amount the tires steer in toward each other or away from each other.  The best way to check this (making the assumption that your frame rails are straight) is to measure the distance from the bicycle rim at the front of the wheel to the frame rail and make sure that the distance from the rim at the back of the wheel to the frame rail is the same.  If there is any error, you are better off with very minor toe-in (wheels pointed at each other at the front side).  This may take some tweaking, so don’t secure the lag bolts all the way until you have your mounting plates in the right position.

Here are some different views to show how everything goes together.

015-4 - Stackup 2

015-4 - Inboard view as installed

015-4 - Installed completely

015-4 - Front view installed

015-4 - Top view installed

There you go, bicycle wheels delivering calories, rather than helping burn them!

Up next…

Getting the keezer onto the Bierwagen

 

 

Mein Bierwagen Part 2 – Building the Frame

This post will present the basic plans to construct the wooden frame of the Bierwagen.

Difficulty: level_3

This project just requires some basic building skills, but you might need some help getting the keezer onto the Bierwagen.

Posts for this Project:

Part 1: Introduction
Part 2: Building of the frame (this post)
Part 3: Bicycle wheel attachment
Part 4: Getting the keezer onto the Bierwagen
Part 5: Keezer collar
Part 6: Storage of the Bierwagen

Affiliate Links

Helpful Tools:

Circular Saw or Miter Saw
Drill or Impact Drill

Materials Needed:

  • (qty 6) 2×4 x 96″ boards
  • drywall/deck screws (2.5″ is perfect for most of the joints where you have two 2×4’s side-by-side (3″ total thickness at that point)

Overview:

Here are a few views of the cart (without support legs attached) for reference.

015-2 - Front 3_4 View

015-2 - Rear 3_4 view

This is the cart flipped over so you can see the attachments for the wheels.  The fabrication of those will be in a subsequent post.

015-2 - Back View

Construction:

I’m not going to do a step by step, since the pictures and following information should be sufficient for most readers taking on this task.

Design:

Below is the top view of the cart with only the major dimensions shown.  I had several constraints when designing the cart.  As I mentioned in the first post, it will be rolled out for a grand unveiling at our party.  It had a few obstacles to navigate during it’s trip from the garage to the back yard.

  • It must fit through our gate
  • It must be able to navigate large bumps (edge of driveway and protruding tree roots in the grass)
  • Quick disassembly and assembly for storage under our deck during the other 364 days of the year
  • Utilize our bike tires
  • Integrated ramp system for easy loading/unloading of my keezer dolly
  • It needed to be sturdy enough to stand on that I could switch over kegs during the party
  • The weight of the keezer must be carefully balanced so that the Bierwagen does not tip when set to rest, yet far enough back that lifting from the front is easy.

You can see the profile of the keezer dolly on the top view to show that it is sufficiently in front of the axle line to prevent tipping.  You’ll see in the loading/unloading post how it slides up the “ramp” to be set in place.  I added an extra 1/4″ clearance to the outer edges of the casters so that they would not rub on the frame rails when moving.  I also had to add about 4″ of clearance for the bike wheels.  The Bierwagen is probably overbuilt and pretty heavy to lift, but it serves it’s purpose that one day of the year where it counts!

015-2 - Top_View

The side view shows all of the other major dimensions and locations of the boards.  Again, you can see how the center of the keezer dolly is between the bicycle wheel axles and the legs.  When changing kegs over during the party it is important to stand between the keezer and the legs.  This will also prevent tipping.  You’ll see on the post where the keezer is getting loaded onto the “ramp”, that the standard 3.5″ height of a 2×4 is just low enough to get my keezer dolly up onto, but if you need a little more clearance, you could put an optional cut into the end to get you what you need.

015-2 - Side_View

REMEMBER, IMPORTANT TO AVOID TIPPING!!!!!!:

  • MAKE SURE THE WEIGHT (CENTER OF GRAVITY, CENTER OF MASS, ETC) OF THE KEEZER IS BETWEEN THE WHEEL AXLE LINE AND THE FEET
  • MAKE SURE YOU STAND BETWEEN THE KEEZER AND THE LEGS WHEN MESSING AROUND INSIDE THE KEEZER OR WITH THE KEEZER

Cut list:

Below is the cut list if your Bierwagen ends up matching mine.  I was able to build my cart from a quantity of six, 2x4x96″ studs.  The color coding is consistent with the downloadable guide.

The legs and cross-member supports required mitered ends.  The lengths shown are for the full-length board that you will then trim the angles in the boards.

015-2 - Cut_List

Of course, your keezer is most likely a different size and you may not even have a keezer dolly, so take my plans and modify them to suit your needs.  The cut list is in an ideal world, so you may have to buy an extra 2×4 or if you are like me, you’ve always got some on hand for whatever needs may pop up.

Download the Detail Prints for Frame and Cut List by subscribing:

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

By clicking on the download, you agree to the terms of this license and to be added to the awesome fermware.com subscriber list. Don’t worry, you won’t receive a bunch of trub in your inbox.

Up next…

Bicycle wheel attachment

Posts for this Project:

Part 1: Introduction
Part 2: Building of the frame (this post)
Part 3: Bicycle wheel attachment
Part 4: Getting the keezer onto the Bierwagen
Part 5: Keezer collar
Part 6: Storage of the Bierwagen

 

 

Mein Bierwagen

My wife and I throw our annual Strausstoberfest party every year on the last Saturday in September.  This occurs during the traditional Oktoberfest celebration.  Oktoberfest is synonymous with beer, awesome food and a certain amount of over the top pomp and circumstance.  For the last part, I decided that the beer I’ve spent the last 2+ months caring for MUST have a grand entrance.

Difficulty: level_3

This project just requires some basic building skills, but you might need some help getting the keezer onto the Bierwagen.

Time Required:

An afternoon for the build of the cart.  Longer if you want to paint or stain it.

Posts for this Project:

Part 1: Introduction (this post)
Part 2: Building of the frame
Part 3: Bicycle wheel attachment
Part 4: Getting the keezer onto the Bierwagen
Part 5: Keezer collar
Part 6: Storage of the Bierwagen

Affiliate Links

Overview:

Here I am rolling out the Bierwagen.  Notice the tap handles I made in the post Super Easy Tap Handles.

015-1 Roll out the Bierwagen

Here I am “tapping the keg” with my son looking on.  o’zapft is!

015-1 Tapping the Bier

Here is a 2015 update.  I’ve got my Hipster Cream Ale WBHY 3D printed tap handle as well as a 3D printed Darth Vader bust added to my Super Easy Tap Handles.

015-Strausstoberfest 2015 Bierwagen

The “rolling chassis”.  It uses the front wheels from my bike and my wife’s bike.  We don’t use them much in the fall, so why not be resourceful and use them?

015-1 Rolling chassis

The Bierwagen works in concert with my Keezer Dolly.

015-1 Keezer dolly onto Bierwagen

Nothing too novel here, just another keezer collar and my Ranco temperature controller mounted on back.

015-1 Ranco mounted on back

Stay tuned for my updates on the build for this project.

Up next…

Building of the frame